UV-based advanced oxidation processes for the treatment of odour compounds: Efficiency and by-product formation

The occurrence of the taste and odour compounds geosmin and 2-methyl isoborneol (2-MIB) affects the organoleptic quality of raw waters from drinking water reservoirs worldwide. UV-based oxidation processes for the removal of these substances are an alternative to adsorption and biological processes, since they additionally provide disinfection of the raw water. We could show that the concentration of geosmin and 2-MIB could be reduced by VUV irradiation and the combination of UV irradiation with ozone and hydrogen peroxide in pure water and water from a drinking water reservoir. The figure of merit EE/O is an appropriate tool to compare the AOPs and showed that VUV and UV/O₃ yielded the lowest treatment costs for the odour compounds in pure and raw water, respectively. Additionally, VUV irradiation with addition of ozone, generated by the VUV lamp, was evaluated. The generation of ozone and the irradiation were performed in a single reactor system using the same low-pressure mercury lamp, thereby reducing the energy consumption of the treatment process. The formation of the undesired by-products nitrite and bromate was investigated. The combination of VUV irradiation with ozone produced by a VUV lamp avoided the formation of relevant concentrations of the by-products. The internal generation of ozone is capable to produce ozone concentrations sufficient to reduce EE/O below 1 kWh m⁻³ and without the risk of the formation of nitrite or bromate above the maximum contaminant level.     

Modeling the mechanical properties of optimally processed cordierite–mullite–alumina ceramic foams by X-ray computed tomography and finite element analysis

Bulk and cellular cordierite ceramics were prepared from a non-stoichiometric powder consisting of corundum, talc (triclinic), α-quartz, K-feldspar, kaolinite, mullite and a small amount of a glass phase. The optimal sintering processing route was evaluated to obtain good mechanical properties. A high flexural strength of 120 MPa and a Young’s modulus of 99 GPa were achieved. The ceramic foams were fabricated by impregnation of polymer preforms with the optimized stock suspension. The mechanical properties of ceramic foams were studied by impulse excitation and compression tests. The Gibson–Ashby model predicted the ceramic foam’s effective modulus and its elastic limit strength well, as measured experimentally. In addition, the actual three-dimensional (3-D) structure obtained from X-ray computed tomography (CT) coupled with the finite element method (FEM) was used to calculate the Young’s modulus and the elasticity limit of the ceramic foam; however, this did not produce aby better agreement between the calculated values and the experimental results. The discrepancy between the Gibson–Ashby model and FEM could probably be attributed to the accuracy and small volume of representative reconstructed 3-D cellular structure. Taking account of the effect of the internal hollow structure on the stress localization in the ceramic struts, the CT–FE modeling provides a good measure of the adaptability and predictability of actual ceramic foam structures for realistic damage modeling.     

Investigation of the long term effects of moisture on carbon fibre and epoxy matrix composites

The aim of this work is to investigate the long term effects of moisture on the interface between a carbon fibre and an epoxy matrix. High modulus carbon fibres were used to prepare single fibre model composites based on an epoxy resin. The samples were immersed in the seawater and demineralised water and their moisture uptake behaviour was monitored. The equilibrium moisture content and diffusion coefficients for the samples were determined. DSC has been used to analyse the moisture effects on glass transition temperature and thermal stability of the pure epoxy specimens. These results showed a reduction in the glass transition temperature (T_g) after moisture absorption. Tensile tests were also carried out for the epoxy specimens and a general decrease in the mechanical properties of the epoxy matrix was observed. Raman spectroscopy was used to observe the effects of moisture on the axial strain of the carbon fibre within the composite and stress transfer at the interface as a function of exposure time. The results show that the decrease in the mechanical and interfacial properties of the model composites under the seawater immersion is more significant than under demineralised water immersion.     

混合粉的充模能力

粉末冶金混合粉的质量常用标准技术,如霍尔流动性、松装密度等进行研究.可是这些技术在预测生产性能上是有限的.为此,开发出一种充模模拟器.表征矩形模的填充以确立模宽与取向对混合粉填充密度的重要性.而且研究了混合粉的粘结对充模的影响,特别是在进料靴的最大可能速度下进行研究.根据压制中对填充性能的影响,对结果进行了讨论.     

Thyristor Converters for Traction DC Motor Drives

Based on tests in laboratories and on German Federal Railways (GFR) trial vehicles type ET 25 as well as on an industrial locomotive type 500 of the Rheinische Braunkohlen AG the subsequent development has been concentrated on the improvement of the power factor ? and the displacement factor cos ? in four vital stages: 1) introduction of half-control, unsymmetrical half-controlled, fully-controlled single-phase bridge connection with specially designed control systems: 2) introduction of sequence connection of several half-controlled bridges; 3) optimization of the so far applied connections for major assemblies such as rectifier transformer, rectifier, and smoothing reactor for improving the power factor; 4) introduction of sector control with self-commutating unsymmetrical bridge for improving the power factor.     

Remotely actuated polymer nanocomposites--stress-recovery of carbon-nanotube-filled thermoplastic elastomers

Stimuli-responsive (active) materials undergo large-scale shape or property changes in response to an external stimulus such as stress, temperature, light or pH. Technological uses range from durable, shape-recovery eye-glass frames, to temperature-sensitive switches, to the generation of stress to induce mechanical motion. Here, we demonstrate that the uniform dispersion of 1-5 vol.% of carbon nanotubes in a thermoplastic elastomer yields nanocomposites that can store and subsequently release, through remote means, up to 50% more recovery stress than the pristine resin. The anisotropic nanotubes increase the rubbery modulus by a factor of 2 to 5 (for 1-5 vol.%) and improve shape fixity by enhancing strain-induced crystallization. Non-radiative decay of infrared photons absorbed by the nanotubes raises the internal temperature, melting strain-induced polymer crystallites (which act as physical crosslinks that secure the deformed shape) and remotely trigger the release of the stored strain energy. Comparable effects occur for electrically induced actuation associated with Joule heating of the matrix when a current is passed through the conductive percolative network of the nanotubes within the resin. This unique combination of properties, directly arising from the nanocomposite morphology, demonstrates new opportunities for the design and fabrication of stimuli-responsive polymers, which are otherwise not available in one material system.